In some cases the 1/8" Stereo - 1/8" Stereo cable may not be needed if the turntable has several headphone jacks.
One plug will be used for headphones (we are assuming that the headphones have a classical 1/8" stereo-out male connector) and the other for the line-in on the PC audio card. Obtain Dual Short 1/8" Stereo - 1/8" Stereo cable with two female endings (also known as Dual Headphone Jack splitter). The turntables that do not have the USB or Fire wire audio output connections can be attached to the PC with the Long male to male 1/8" Stereo - 1/8" Stereo cable Here are the cables that can be used to connect the turntable to the PC: Step 1.
The PC should have the hardware drivers installed for the turntable and recognize it as a valid audio input device. Most new turntables have USB or FireWire audio output build-in so they can be easily connected to the PC.
How to Broadcast Live using turntables? To broadcast using Shouthost the live content from the turntable, you will need to install the software that would allow you to connect your turntable to the PC. Congratulations, you have begun to stream audio! You may now open any Winamp-compatible audio file in your player, and it will stream to our servers. In the status box above the button, it should give a time and then "Sent xxxx bytes". Make sure "Output 1" is selected, and then click the connect button. Go back to the "Output" tab in your DSP window. As every soundcard is different and individual, we cannot give any tutorials for the Soundcard Input. Unless you have specific soundcard input settings, or want to talk on your stream, select "Winamp" at the Input Device. Input settings (select the input audio source) Select the "Input" tab at the top of your DSP window. Note: If you try streaming at a bitrate higher than what you have ordered you will not be able to stream and your server may shut itself off. In the Encoder Settings drop down, select the bitrate that you ordered from us, and be sure that the line you selected has "Stereo" at the end, so individual sounds will come out of both of your listeners speakers. AAC+ is only compatible with Winamp and Windows Media Player (with a plugin), but sounds much better at lower qualities. MP3 audio sounds alright, but is compatible with just about every media player on the market. The Encoder Type can be set to either MP3 or AAC+, our servers support both. Make sure under the selection box, you have selected "Encoder 1". Be sure to check the "Enable Title Updates" and the two boxes that say "Auto" in order to show your users the title of the song that is playing.Įncoder Settings (select streaming audio format) Select the "Encoder" tab at the top of your DSP window. If you'd like your server to be listed in the SHOUTcast directory, check the "Make this server public" box, and fill in all of the information below the box in a proper manner. Yellowpage setup (streaming server display details) Click on the "Directory" tab right above where you entered all of the previous information.
There is sometimes a space added during the process that will cause an invalid password error) (Common mistakes include using the copy and paste method. Enter this here, and make sure there are no mistakes. Password: Last, you need to enter the encoder (source) password that was given to you in your welcome email. Once again, this must be set properly or else you will be unable to connect. Port: In this field, you need to enter the port that was given to you in your welcome email. Make sure that you put in the proper server IP, or else you will not be able to connect. Address: Here, you need to enter the server IP that was given to you in the welcome email you received. Select "Output 1" under the selection box, and fill in all of the following fields properly. Select the "Output" tab at the top of your DSP window. Please refer to the picture below: If you see "Nullsoft SHOUTcast Source DSP v2.3.2" in the right panel, then you have correctly installed the SHOUTcast Broadcast DSP Plug-in.
Step 1.) For the install On your pc it's very simple download latest version of winamp Download Winamp install it first (For Windows) and Download SHOUTcast DSP Plug-In For Winamp (For Windows) Once you have installed the DSP, start Winamp, open the preferences(CTRL+P) and click on the DSP/Effects subcategory under the Plug-ins tree. How To Connect How to Broadcast to your ShoutHost Server using Winamp?